Archimedes Principle Lab Manual, Lab Reports of Physics

Download Archimedes Principle Lab Manual and more Lab Reports Physics in PDF only on Docsity! Brooklyn College 1 ARCHIMEDES’ PRINCIPLE Purpose a. To study buoyant force as a function of submersed volume. b. To verify Archimedes’ Principle. c. To use Archimedes’ Principle to determine the densities of a solid sample and a liquid sample. Theory a. Buoyancy and Archimedes’ Principle When an object is submerged in a fluid, it experiences a buoyant force, B. This buoyant force is the resultant of the pressure-based forces on the surfaces of the submerged object. The pressure is higher at greater depths in the fluid, and thus the buoyant force is directed upward. Figure 1. The buoyant force B is the resultant of the pressure-based forces. Archimedes’ Principle, which is derived in your textbooks, states that the magnitude of the buoyant force is equal to the weight of the fluid displaced by the submerged object. B = Wdisplaced-fluid = mdisplaced-fluid g = fluid Vdisplaced-fluid g . (1) If the object is completely submerged in the fluid, the volume of displaced fluid is equal to the volume of the submerged object: Vdisplaced-fluid = Vobject. Then B = fluid Vobject g . (2) If the object is partially submerged, Vdisplaced-fluid = partial volume of the object that is submersed. For a cylindrical solid object of uniform cross section area (A), if the cylinder is immersed in a fluid along the axis of the cylinder and h is the height of the object in the fluid, B = fluid Vimmersed g = fluid Ah g. (3) Brooklyn College 2 b. Effect of buoyancy on measurements of mass When an object is hung from a scale, the reading of the scale, mapparent, is based on the tension in the wire connecting the object to the scale: Wapparent = mapparent g = Twire. Normally, Twire = Wobject = mobject g, and the reading of scale, mapparent, is an accurate measurement of mobject. However, if the object is hung from the scale while submerged in a fluid, then Twire < Wobject because of the contribution of the buoyant force B. Specifically, writing down the balance of the forces on the object (see Figure 2): 0 = Fy = Twire + B – Wobject . Figure 2. The equilibrium of forces on an object hanging from a scale while submerged. Since the scale reading is always based on Twire, Wapparent = Twire = Wobject – B . B = Wobject – Wapparent (4) The apparent weight of a submerged object is less than its actual weight, and the difference between these weights is the buoyant force. What will happen to the apparent weight if the object is partially submerged? In this lab we will measure apparent weight of objects in different conditions to verify Archimedes’ Principle as well as use this principle to determine the density of solid and liquid samples. Apparatus Spring scale, aluminum cylinder block, Tall graduated cylinder, laboratory jack, stand, clamp, Triple beam balance, Vernier calipers, metal cylinder with copper wire attached, hollow wooden block, beaker, tap water, liquid X, paper towels for drying. Brooklyn College 5 Part III. For determining the density of liquid X using Archimedes’ Principle. 12. Now, place a beaker of liquid X on the adjustable platform above the scale pan, and hang the metal cylinder so that it is completely submerged in liquid X. Record the reading of the triple beam balance for the hanging submerged cylinder in Table 4. Remove the cylinder and dry it. Extra activities 1. Measure the volume of the wooden block my submerging it in a graduated beaker of water. Since the block naturally floats, you will need to hold it under the water using something of negligible volume, like a wire. Compare this measured wooden block volume to the volume determined using Archimedes’ Principle. 2. Measure the density of liquid X by pouring some in a graduated beaker and measuring its mass with the scale. You will also need to measure the mass of the empty beaker. Compare your measured liquid X density to the value determined using Archimedes’ Principle. Computation 1. For part I of the experiment, calculate the buoyant force for each volume in the Table 1 using Eq. 4. 2. From the data in the table, plot a graph of buoyant force, B, as a function of V. Make sure to label the axes appropriately. Does the graph look linear? 3. Draw a best fit line and find the slope of the line. What is the significance of the slope? From the slope the graph, determine the density of the water. 4. For other parts of the experiments, calculate and complete the tables based on the data from the measurements. Densities of the metal cylinder and water will be provided. Include your final results in your report. 5. One of the achievements of Archimedes was the ability to determine the volume of an object by measuring the volume of water displaced upon being submerged. In this lab, you applied Archimedes principle to measure the volume of the cylinder and in addition, the volume of the block. Use a set of calipers to measure both the volume of the cylinder and the volume of the block. Compare your experimentally determine volume for the cylinder and the block by Archimedes principle to that determined using the calipers. Be sure to check this prior to leaving the laboratory. Discuss the data in the lab report. 6. While the density of wood varies, how does your measured density for the wooden block compare to known values? You can look up some common wood densities on the internet. Discuss your data in the lab report. Questions 1. If a string is attached instead of the spring scale in part I of the experiment, how does the tension in the string vary if the cylinder is slowly submerged into the liquid? 2. What do you expect the slope of the curve in part I if salt water is used instead of fresh water? 3. When using the scale to measure the mass of the cylinder in step 8, does it experience a buoyant force due to its immersion in air? If so, approximate the magnitude of this buoyant force. 4. When using the scale to measure the submerged cylinder in step a3, does it matter if the cylinder touches the bottom of the beaker in which it is submerged? How would such contact affect your measurement, if at all? Brooklyn College 6 Data Sheets Date experiment performed: Name of the group members: Table 1. Studying buoyant force with partially immersed volume From the graph of buoyant force (B) versus volume (V), Slope of the curve = Density of the liquid = Volume Immersed, V (mL) Spring Scale Reading, Wapp (N) Buoyant Force, B (N) 0 4 8 12 Brooklyn College 7 Tables for measurements and calculations (measurements in shaded boxes) Table 2 for verifying Archimedes’ Principle for cylinder submerged in water Mass of cylinder (measured in g, converted to kg) Weight of cylinder Wcylinder (calculated in N) Apparent mass of cylinder submerged in water (measured in g, converted to kg) Apparent weight for cylinder submerged in water (calculated in N) Buoyant force, B, based on difference between Wcylinder-apparent and Wcylinder (calculated in N) Diameter of cylinder (measured in mm, converted to m) Height of cylinder (measured in mm, converted to m) Volume of cylinder (calculated in m 3 ) Buoyant force, B, based on Archimedes’s Principle Percent error between B measured with scale and B based on Archimedes’ Principle