Lab 2: DC Circuits Lab Assignment - Laboratory Physics 1 | PHY 4802, Lab Reports of Physics

Download Lab 2: DC Circuits Lab Assignment - Laboratory Physics 1 | PHY 4802 and more Lab Reports Physics in PDF only on Docsity! 2 class days Lab 2: DC Circuits Lab Assignment 1. I-V curve for various components Source: Curtis, 1.2.1. (HH 1.1, 1.2, 1.3) A passive element is a two-contact device that contains no source of power or energy; an element that has a power source is called an active element. In the first part of the laboratory, you are to measure and plot the I-V curve for various passive circuit elements. You are also to plot the power dissipation in each element vs. applied voltage. You need to decide which of the circuit elements are resistive and which are not resistive. For those elements that are resistive, determine the resistance, R. To do these measurements, you will connect the device under test to a variable voltage power supply and measure I and V as you vary the voltage control of the power supply. Make a table of all your data points and plot them as you go along. Reverse the polarity of the applied voltage by reversing the orientation of the element; this allows you to do measurements from -15 to +15 volts on the supply. Measure the I-V curves and the power dissipation of the following elements. When making these measurements, record the applied voltage from the supply, the voltage across the device from the voltmeter, and the current through the device: • 10k resistor • 1k resistor • #47 lamp: Follow instructions and answer all questions from HH 1.2 • diode: Follow instructions from HH 1.3 carefully. Answer/do all parts on page 27. Do not answer the questions on page 28. Plot the power dissipation vs. applied voltage. Indicate the equation used to calculate power. 2. Effects of instruments on your readings Source: http://www2.hawaii.edu/~jrand/EE211/Labs/01_analog_measuring_equipment.doc (HH 1.1) Part A - Voltmeter An ideal voltmeter has infinite resistance: It is an open circuit. Although it is impossible to make a physical voltmeter with infinite resistance, a well-designed voltmeter exhibits a very large internal input resistance. In some experiments, it is important to take into account the finite, non-ideal, internal resistance. To determine the internal resistance of the voltmeter, set up the circuit shown in Figure 1. The voltmeter reads the voltage across itself, which includes its internal resistance. Since the circuit has only a single branch, the current flowing through the resistor also flows through the voltmeter. The current is given by the equation: I = Vsource - Vmeter (1) R From Ohm's Law, if we know the current (I) and the voltage of the meter (Vm) we can compute Rm. Rm = R * Vm (2) Vs – Vm + - 10V 1M Vol tmeter Figure 1: Circuit for measuring the resistance of the voltmeter. 1. Select a 1MΩ resistor, and measure its value using the multimeter. 2. Set the power supply to provide 10 V (Remember, always measure the voltage provided by the power supply with either the voltmeter or the scope. Do not rely on the digital display on the front panel of the power supply.) 3. Record the voltage measured by the voltmeter. 4. Compute the internal resistance of the voltmeter. What is the total resistance of the voltmeter? accurately than it can be measured, so you may as well stop measuring it. Why is this the case? 2. Measure the open-circuit voltage and short-circuit current of your bridge circuit, then construct the Thévenin equivalent circuit using a variable dc power supply. Use a series combination of resistors or a variable resistor (potentiometer) to approximate the required value RTh within 5%. Now repeat the measurements of part 1 on this equivalent circuit. Use Kirchoff’s laws to solve directly for the voltage and current as a function of the load resistance RL. Compare the results with your measurements from part 1. Comment on the accuracy of your results from part 2. What contribution to the error comes from the inexact value you used for RTh? From the finite resistance of the voltmeter? From the finite resistance of the current meter? 4. Resistor Power Rating Source: Hands-on 2.2.1 Caution: In the following exercise, care must be taken to prevent burns. The resistor in the following exercise will become very hot and may even catch fire (briefly). Keep the body of the resistor well above the breadboard. Do not touch the resistor with your fingers. Remove the destroyed resistor using pliers or a similar tool. Be sure that the power is turned off, and construct the circuit shown using a 1/4 watt carbon-film resistor. This circuit can be used to demonstrate destructive power loading. Note that the resistor will heat up rapidly. You may substitute a 100 Ω resistor if we don’t have any 68’s. You must use the variable DC power supply for this exercise! Turn on the power and observe the effect on the resistor. Be sure to turn off the power as soon as the resistor begins to smoke. Record your observations and comments. Calculate the power that was dissipated by the resistor before it burned out. What is the minimum resistor value that can be safely used in this circuit? (Assume that only 1/4 watt resistors are available.) Calculate the current that flowed through the resistor (before it burned out). Note that even though the voltage was low and the current was well under 1 A, damage was nevertheless done! Because your body’s resistance is large, low voltages can’t give you a shock, but in the wrong circumstances they can still cause trouble. The key to safe work in electronics is always to estimate power dissipations in components before turning on the power, and to make sure you are not exceeding the ratings.