Reviewer of pipe design, Exercises of Mathematics

Download Reviewer of pipe design and more Exercises Mathematics in PDF only on Docsity! 1 INDUSTRIAL & POWER PLANT DESIGN ELEMENTS PROBLEMS & ELEMENTS (With Answer and Solution) 1. In Refrigeration, how do you call a heat exchanger in which low-pressure refrigerant boils or vaporizes, thus absorbing heat that was removed from the refrigerated area by the cooling medium (water)? a) Evaporator b) Chiller c) Cooler d) Flooded Evaporator Answer: b) Chiller. In refrigeration application, the appropriate term used for evaporator is chiller. 2. In an ideal standard Brayton cycle, 1.5 kg/s of air at 101 kPaa and 27 o C is compressed isentropically to a certain pressure and temperature after which the is added until the temperature becomes 1027 o C. Isentropic expansion occurs in the turbine. Determine the net power produced by the cycle. a) 629.56 kW b) 592.65 kW c) 529.76 kW d) 579.26 kW Answer: c) 529.76 kW Solution:    o 2 4 1 4T T TT 300 1300 624.5 K            kW76.5293005.624213000062.15.1TT2TmcW 123pnet  3. In an air standard Otto cycle, the clearance volume is 12 % of the displacement volume. What is the thermal efficiency? a) 57 % b) 59 % c) 58 % d) 60 % Answer: b) Thermal efficiency = 59 % Solution: D2 V12.0V  33.9 12.0 12.1 V12.0 VV12.0 V VV V V r D DD 2 D2 2 1 k              %08.59%100 33.9 1 1%100 r 1 1e 4.01k k th                     4. It is a type of refrigeration system where only part of the circulated refrigerant is evaporated, with the remainder being separated from the vapor and then recirculated. How do you call this system? a) Absorption refrigeration system b) Vacuum refrigeration system c) Vapor-compression refrigeration system d) Flooded refrigeration system Answer: d) Flooded refrigeration system 5. In an air-standard Brayton cycle, air enters compressor at 1 bar and 15 o C. The pressure leaving the compressor is 0.6 MPaa and maximum temperature of the cycle is 1000 o C. What is the maximum net work, in kJ/kg? a) 319.52 b) 392.51 c) 315.29 d) 352.19 Answer: d) Max Wnet = 352.19 kJ/kg Solution:    K49.605273100027315TTT o 312         kg/kJ19.35228849.605212730062.1TT2TcwMax 123pnet  1 2 3 4 300 o K 1300 o K T s 2 6. How do you call the ice formation on a refrigeration system at the expansion device, making the device inoperative? a) Ice formation b) Freeze-up c) Freezing d) Pump-down Answer: b) Freeze-up 7. What is the clearance volumetric efficiency of an ammonia compressor designed with 4 % clearance and operating between condenser temperature of 30 o C (psat = 1.1672 MPaa) and evaporator temperature of 4 o C (psat = 497.48 kPaa)? a) 93.61 % b) 93.68 % c) 96.31 % d) 96.83 % Answer: c) Volumetric Efficiency = 96.31 % Solution:     %31.96%100 48.497 2.1671 04.004.1%100 p p cc1 304.1 1 k 1 s d v                                      Note: k = 1.304, for ammonia (R-717) k = 1.30, for R-134a 8. In a lithium bromide solution absorption refrigeration system, which of the following is the function of water? a) Refrigerant b) Absorbent c) Coolant d) Analyzer Answer: a) Refrigerant. Water serves as refrigerant while the lithium bromide serves as the absorbent. In ammonia solution absorption refrigeration system, water serves as the absorbent while ammonia serves as the refrigerant. 9. The percent rating of water tube boiler is 200 %, factor of evaporation is 1.10, and heating surface is 400 ft 2 . Determine the rate of evaporation, in kg/hr. a) 1831 b) 1831 c) 1138 d) 1813 Answer: c) Rate of evaporation = 1138 kg/hr Solution: 40 10 400 10 .S.H Hp.BoRated      80402Hp.BoRatedRatingPercentHp.Bo.Dev      .E.F2257mhhmHp.Bo.Dev sB1s      hr/kg1138 1.12257 3143580 FE2257 Hp.Bo.Dev ms  10. In the absorption refrigeration system, is a pressure vessel mounted above the generator through which the vapor leaving the generator pass. How do you call this component? a) Absorber b) Analyzer c) Rectifier d) Reflux Answer: b) Analyzer or bubble column 11. A Carnot cycle is represented by a rectangle in a Ts diagram that operates between temperature limits of 300 o K and 650 o K. Inscribed within a rectangle is a ellipse of maximum major and minor axes, represents a cycle and operating at the same temperature limits. Considering that the major axis of the ellipse is two times that of its minor axis. Determine the thermal efficiency of the cycle represented by an ellipse. a) 44.88 % b) 48.48 % c) 43.66 % d) 46.36 % Answer: a) 44.88 % Solution: TH = 650 K TL = 300 K Tm = 475 K a b 5 Solution:   psia34.12Hgin12.25ft8004 ft0001 Hg"1 Hgin92.29p          Note: Barometric pressure reduces by 1 inch Hg per 1000 ft rise in elevation or 83.312 mm Hg per 1000 m rise in elevation. Barometric temperature reduces by 3.566 oF per 1000 ft rise in elevation, or 6.5 oC per 1000 m rise in elevation. 23. It the maximum temperature of any gas or vapor at which it may be condensed into a liquid; above this temperature, it is impossible to condense regardless of the pressure applied. How do you call this temperature? a) Saturation temperature b) Superheated temperature c) Critical temperature d) Dew point temperature Answer: Critical temperature 24. Calculate the energy transfer rate across 6” wall of firebrick with a temperature difference across of 50 o C. the thermal conductivity of the firebrick is 0.65 Btu/hr-ft- o F. a) 369 W/m 2 b) 369 Btu/hr-Ft 2 c) 639 W/m 2 d) 639 Btu/hr-Ft 2 Answer: a) Heat Transfer = 369 W/m 2 Solution:       2 o ftHr/Btu11750 5 9 ft 12 6 Ffthr/Btu65.0 T L k A q                  2 2 2k m W 88.368 m1 ft28.3 s3600 Hr1 Btu/J1055ftHr/Btu117 A q                  25. Any refrigerant that exists as a liquid under normal atmospheric pressure and temperature must be vaporized in an evaporator under a pressure below atmospheric. This is sometimes referred to as: a) Halogenated refrigerant b) Freon refrigerant c) Vacuum refrigerant d) Halocarbon refrigerant Answer: c) Vacuum refrigerant 26. What is the specific gravity of a fuel at 28o Baume? a) 0.868 0.688 c) 0.886 d) 0.986 Answer: c) SG = 0.886 Solution: 886.0 13028 140 130Baume 140 C6.15@SG o o      27. Air at 1 MPaa and 310 oC is expanded to 250 kPaa in accordance with the relation pV1.25 = C. Determine the work done. a) + 162.11 kJ/kg b) – 162.11 kJ/kg c) + 126.11 kJ/kg d) – 126.11 kJ/kg Answer: a) Work done, W = + 162.11 kJ/kg Solution:   K83.441 1000 250 273310 p p TT o25.1 25.0 n 1n 1 2 12                     kg/kJ11.16258383.441 25.0 28708.0 TT n1 R n1 vpvp W 12 1122                   Note: Work is positive (+), if work is done by the system; and work is negative (-) if work is done to the system. 6 28. It is any one of a group of refrigerants that have been developed since about 1925 to overcome the irritating or toxic effects of refrigerants, such as ammonia and sulfur dioxide and the high condensing pressures required with carbon dioxide. How do you call these refrigerants? a) Halogenated refrigerants b) Freon refrigerants c) Vacuum refrigerants d) Halocarbon refrigerants Answer: a) Halogenated refrigerants 29. A Rankine cycle operates with a thermal efficiency of 40 % and the factor of evaporation of the boiler is 1.15. Determine the mass flow rate of steam if the cycle power output is 5.5 MW. a) 5.3 kg/s b) 4.3 kg/s c) 3.5 kg/s d) 6.3 kg/s Answer: a) Steam mass flow rate, ms = 5.3 kg/s Solution: kW75013 40.0 5500 e W Q th net A      s/kg3.5 15.12257 75013 FE2257 Q hh Q m A B1 A s    30. This refrigeration system component combines the functions of a cooling tower and a condenser. It consists of a casing enclosing a fan or blower section, water eliminators, refrigerant condensing coil, water pan, float valve, and spray pump outside the casing. How do you call this component? a) Water-cooled condenser b) Evaporative condenser c) Atmospheric condenser d) Chiller Answer: b) Evaporative condenser 31. A boiler operates at 82 % efficiency while the mass of steam generated is 490 200 kg in 6 hours. The enthalpy of steam is 3187 kJ/kg and feed is 604.83 kJ/kg while the fuel used for boiler has a heating value of 32 567.85 kJ/kg. Find the mass of fuel needed per day in metric tons. a) 179.6 b) 189.6 c) 198.6 d) 169.8 Answer: b) Fuel consumption per day = 189.6 metric tons Solution: hr/kg70081 6 200490 ms      hr/kg7.303272257 82.0 83.604318770081 E hhm Q B 12s F      day/tonsMetric6.189day/kg8958.589189hr/kg58.8997 85.56732 7.303272257 q Q m h F F  32. It refers to a factor used in calculating the over-all heat transfer through the tube walls of a condenser tube or other heating surface. It includes the sum of the heat-transfer rate of the layer of dirt and foreign material that builds up on the water side of the tube. What is this factor? a) Cooling factor b) Contact factor c) By-pass factor d) Fouling factor Answer: d) Fouling Factor 33. A 10 kg/s of air enters the theater at 16 o C. The theater is to be maintained at 27 o C DB and 20 o C WB. If the sensible heat ratio is 0.71, what is the latent heat load of the theater? a) 45.21 kW b) 54.21 kW c) 110.682 kW d) 42.51 kW Answer: a) atent heat load, qL = 45.21 kW Solution:       kW682.1101627100062.1ttm0062.1q srs  kW21.45682.110 71.0 682.110 q SHR q q s s L  34. It is a refrigeration system evaporator which is arranged with a tank or a single drum (accumulator) located above the coil so that the inside of the evaporator is full of refrigerant. How do you call this type of evaporator? 7 a) Flooded evaporator b) Dry evaporator c) Cooing coil evaporator d) Headered coil evaporator Answer: a) Flooded evaporator 35. A 80 MW power plant has an average load of 34 500 kW and a load factor of 0.75. Find the reserve power over a peak load power. a) 14 000 kW b) 34 000 kW c) 24 000 kW d) 4 000 kW Answer: b) Reserve Power = 34 000 kW Solution: LoadPeak LoadAverage FactorLoad  kW00046 75.0 50034 FactorLoad LoadAverage LoadPeak  kW000344600080000LoadPeakCapacityPlantPowerserveRe  36. What is the standardized term used by the industry to describe any device that meters or regulates the flow of liquid refrigerant to an evaporator? a) Refrigerant control b) Expansion valve c) Throttling valve d) Capillary tube Answer: b) Expansion Valve 37. A steam generator burns fuel oil with 25 % excess air. Fuel may be represented by C14H30. Calculate the actual-air fuel ratio. a) 17.63 b) 18.63 c) 16.63 d) 15.63 Answer: b) Actual A/F ratio = 18.63 kg air per kg fuel Solution:           63.1825.1 301412 3025.01428.137 mn12 e1m25.0n28.137 F:A        Note: Equation above is used for hydro-carbon fuels, CnHm. 38. Define a “control valve”. a) The value set on the scale of the control system in order to obtain the required condition b) The quantity or condition of the controlled medium c) The flow or pressure of the steam (or fluid) being manipulated d) The valve of the controlled condition actually maintained under steady state conditions Answer: d) The valve of the controlled condition actually under steady state conditions 39. A container filled with helium is dropped 3000 m above the ground, find the change of temperature? a) 12.43 o C b) 9.43 o C c) 15.43 o C d) 8.43 o C Answer: b) The change of temperature, T = 9.43 o C Solution: UKEP       T 1k R mTmc 1000 zmg v              R1000 zg1k T   k = 1.666 Kkg/kJ078575.2 4 3143.8 M R R o      C43.9 078575.21000 30008066.9666.0 T o Note: For Helium, k = 1.666 and M = 4 kg/kgmole 40. A pneumatic temperature control is used on the steam supply to a non-storage heat exchanger that heats water serving an office heating system. What is referred to as “manipulated variable”? a) The water being heated b) The air signal from the controller to the valve actuator 10 Answer: b) they operate by holding back condensate until it has cooled 53. The approach and efficiency of cooling tower are 10 o C and 65 %, respectively. If the temperature of water leaving the tower is 27 o C, determine the temperature of water entering the tower. a) 54.57 o C b) 55.47 o C c) 45.57 o C d) 54.75 o C Answer: c) Temperature of water entering the tower, t3 = 45.57 o C Solution: o wb1 4t t CA 27 10 17 C     Tower Efficiency, 3 4 t 3 wb1 t tACR e TCR t t       o4 wb1 3 27 0.65 17t et t 45.57 C 1 e 1 0.65       54. What are the main considerations for steam trap selection? a) Price b) Air venting, plant performance, flow capacity and reliability c) Connections d) The trap must be the same size as the condensate drain line Answer: b) Air venting, plant performance, flow capacity and reliability 55. An air-vapor mixture has a dry bulb temperature of 30 o C and a humidity ratio of 0.015 kg/kg d.a., calculate the enthalpy of the moist air. a) 68.527 kJ/kg d.a b) 86.527 kJ/kg d.a c) 65.827 kJ/kg d.a. d) 67.528 kJ/kg d.a Answer: a) Enthalpy, h = 68.527 kJ/kg d.a. Solution: Using the IHVE formula, h = 1.007t – 0.026 + W(2501 + 1.84t)        dakg/kJ527.683084.12501015.0026.030007.1h  56. Determine the equivalence ratio of the following mixture: 4 grams of butane, C4H10, and 75 grams of air. a) 0.72 b) 0.92 c) 0.62 d) 0.82 Answer: d) Equivalence ratio = 0.82 Solution: Theoretical air-fuel ratio,        kg/kg385.15 10412 1025.0428.137 mn12 m25.0n28.137 Wa        Actual Air-fuel ratio, kg/kg75.18 4 75 Waa  82.0 75.18 385.15 e1 1 W W ratioeEquivalenc aa a    57. Can temperature controlled applications be trapped? a) Traps should not be fitted under any circumstances b) Only if there is no lift after the trap c) If the pressure on the trap is always higher than backpressure d) Pumps should always be fitted to remove condensate Answer: c) If the pressure on the trap is always higher than back pressure 58. Find the air Hp of an industrial fan that delivers 25 m 3 /s of air through a 900 mm by 1200 mm outlet. Static pressure is 127 mm of water gage and air density is 1.18 kg/m 3 . 11 a) 52.3 Hp b) 35.2 Hp c) 42.3 Hp d) 34.2 Hp Answer: a) Fan power, WF = 52.3 Hp Solution:    s/m15.23 2.19.0 25 A Q V    airm63.107127.0 18.1 1000 hh w a w s               airm32.27 8066.92 15.23 g2 V h 22 v  airm95.13432.2763.107hhh vst      Hp3.52kW04.39 1000 95.134258066.918.1 1000 gQh W t F    59. Determine the indicated mean effective pressure of an engine, in psi, having a brake mean effective pressure of 750 kPa and 80 % mechanical efficiency. a) 138 b) 137 c) 136 d) 135 Answer: c) Indicated mean effective pressure, pI = 136.01 psi Solution:    %100 p p %100 W W I B I B m  psi01.136kPa5.937 80.0 750p p m B I    60. Unless they are designed to flood, what is the important when removing condensate from heat exchangers? a) Condensate is allowed to sub-cool before reaching the trap b) Condensate is removed at steam temperature c) Condensate should back-up into the steam pipe d) That the trap is fitted level with or above the heater outlet Answer: b) Condensate is removed at steam temperature 61. The indicator card (actual p-V diagram) of an engine in a Diesel power plant indicates an area of 0.06 m 2 and length of 300 mm, and with a spring scale of 2500 kPa/m. The engine was tested using Prony brake with lever arm of 3 m and tare weight of 8 kN. Determine the mechanical efficiency if the engine is running at 600 rpm. The engine is 2- stroke and has 12 cylinders, 300 mm bore, and 450 mm stroke. a) 78.01 % b) 79.01 % c) 82.01 % d) 76.01 % Answer: b) Engine mechanical Efficiency = 79.01 % Solution:     kW96.1507 30 m3kN8600 30 Tn WB      m2.0 m3.0 m06.0 b A h 2     kPa500m2.0m/kPa2500hkp sI        s/m817.360/1260045.03.0 4 60/LnnD 4 V 32 c 2 D              kW5.1908817.3500VpW DII      %01.79%100 5.1908 96.1507 %100 W W I B m        62. How is flash steam produced? a) From condensate passing from high to low pressure systems b) From saturated steam c) From superheated steam d) From steam mixed with high temperature air Answer: a) From condensate passing from high to low pressure systems 12 63. A 2-kg steam at 2.5 MPaa and 260 o C undergoes a constant pressure until the quality becomes 70 %. Determine the heat rejected, in Btu. At 2.5 MPaa and 260 o C: h = 2907.4 kJ/kg; and at 2.5 MPaa and 70 % quality: hf = 962.11 kJ/kg and hg = 2803.1 kJ/kg. a) 1244.7 Btu b) 1424.7 Btu c) 1442.7 Btu d) 1274.4 Btu Answer: a) Heat rejected = 1244.73 Btu Solution:      kg/kJ803.225011.9621.280370.011.962hhxhh fg2f2        Btu73.1244kJ19.13134.2907803.22502hhmhmQ 12  64. Are steam traps required to pass air? a) Steam traps should not pass air under any circumstances b) Only when the trap has passed all the condensate c) Air should be removed as soon as it reaches the trap d) Only on high pressure steam system Answer: c) Air should be removed as soon as it reaches the trap 65. A 145 000-kW turbo-generator requires 690 000 kg/hr of steam at rated load and 23 000 kg/hr of steam at zero load. Determine the steam rate, in kg/kW-hr, at 75 % of its rated load. a) 4.81 kg/kW-hr b) 3.81 kg/kW-hr c) 5.81 kg/kW-hr d) 2.81 kg/kW-hr Answer: a) Rated load = 4.811 kg/kW-Hr Solution: 000145 00023000690 750108 00023m    m = 523 250 kg/hr hrkW/kg811.4 750108 250523 75  66. How do you call a system employing open sprinklers attached to a piping system connected to a water supply through which is opened by the operation of a fire detection system installed in the same areas as the sprinklers? a) Mechanical sprinkler b) Automatic system c) Wet pipe system d) Deluge system Answer: d) Deluge system 67. What is probably the first consideration when selecting a control system? a) What degree of accuracy is required? b) Is the control for heating or cooling? c) Is a two or three port valve required? d) In the event of power failure, must the valve fail-open or fail-closed? Answer: d) In the even of power failure, must the valve fail-open or fail-closed? 68. The combustion gases of a furnace are separated from its surrounding or ambient air which is 29 oC. The brick wall is 130 mm and has a thermal conductivity of 1.23 W/m-oC with a surface emissivity of 0.81. The outer surface temperature of the wall is 130 oC and with surface air conductance of 15 W/m2-oC. For steady state conditions, what is the total heat transmitted for a surface area of 30 m2? a) 70.33 kW b) 73.30 kW c) 33.07 kW d) 37.30 kW Answer: a) 70.33 kW 690 000 kg/hr 23 000 kg/hr 145 000 kW 108 750 kW m 15 c) The rating is based on a steam pressure of 1.0 bar d) The rating does not allow for condensate forming in the heat exchanger Answer: a) The true connected heat load may be different from the rated figure 81. A heat exchanger has a design rating based on a working pressure of 7 bar g. What would be the effect of supplying the exchanger with steam at 3 bar g? a) The heat output would be greater because the enthalpy of evaporation at 3 bar g is higher than at 7 bar g. b) The heat output would be greater because steam at 3 bar g has a greater volume than steam at 7 bar g. c) Less weight of steam would be required because steam at 3 bar g has a higher enthalpy of evaporation than 7 bar g. d) The output would be reduced because the difference in temperature between the steam and product is reduced. Answer: d) 82. A standard 25-mm outside diameter steel tube (with wall thickness of 1.65 mm) is carrying 0.34 lps of oil. Determine the velocity of flow of oil inside the tube. a) 191 fpm b) 181 fpm c) 171 fpm d) 161 fpm Answer: b) Fluid Velocity = 181 fpm Solution:   mm7.2165.1225t2DD oi      s/m9193.0 0217.0 00034.04 D Q4 V 22 o      =180.92 fpm 83. For any particular tank temperature how does the heat loss from the lid of a closed tank compare with that of bottom? a) They are approximately double those from the bottom b) Losses from the top are approximately double those from the bottom c) Losses from the bottom are approximately double those from the top d) Losses from the top are approximately 4 times those from the bottom Answer: b) Losses from the top are approximately double those from the bottom 84. Helium is used in a Carnot engine where the volumes beginning with the constant temperature heat addition are V1 = 0.3565 m 3 , V2 = 0.5130 m 3 , V3 = 8.0 m 3 , and V4 = 5.57 m 3 . Determine the thermal efficiency if k = 1.666. a) 83.95 % b) 89.35 % c) 85.93 % d) 85.39 % Answer: a) Thermal Efficiency = 83.95 % Solution:       %95.83%100 8 5130.0 1%100 V V 1%100 T T 1e 666.01k 3 2 H L th                                           85. What is the disadvantage of heating a tank by direct steam injection? a) It agitates the solution b) Some of the enthalpy of water is used c) Steam traps are not required d) It dilutes the tank content Answer: d) It dilutes the tank content 86. The existing 2000 TR chiller at a large hospital, where you are assigned as Engineer, must be replaced. Which of the following types most likely to be installed? a) Screw chiller b) Scroll Chiller c) Reciprocating chiller d) Centrifugal chiller Answer: d) Centrifugal chiller 16 Note: Centrifugal chillers are generally selected for their high coefficient of performance, good part-load performance, and cooling capacity. The economics of large-scale applications (such as hospital) generally favor more efficient machines such centrifugal chillers. In this case, a centrifugal chiller is also the only one of the types listed that can provide the needed capacity. 87. The temperature inside a furnace is 320 o C and temperature of the outside is – 10 o C. What is the temperature difference in o R. a) 495 b) 945 c) 594 d) 596 Answer: c) Temperature change, 594 o R Solution:       R59410320 5 9 t 5 9 T 5 9 T o cKR  88. Refrigeration condensers are rated based upon their ability to reject the total heat that comes from which of the following? a) Compressor work and net refrigeration effect b) Superheating c) Subcooling d) Compressor work Answer: a) Compressor Work and net refrigeration effect Note: All the heat removed by a refrigeration system, including the heat it introduces due to the work of the compressor, must ultimately be rejected to the outdoor environment by the condenser. So refrigeration effect and compressor work must be considered. 89. The forced convective heat transfer coefficient for a hot fluid flowing over a cold surface is 225 W/m2.0C for a particular problem. The fluid temperature upstream of the cold surface is 120 0C, and the surface is held at 10 0C. Determine the heat transfer rate per unit surface from the fluid to the surface. a. 24 570 W/m2 b. 52.470 W/m2 c. 24 700 W/m2 d. 24 750 W/m2 Answer: d) 24 750 W/m2 Solution:      2 c c m/W7502410120225Th A q  90. A published „U‟ value from a steam coil to a water based solution is given as 550 – 1300 W/m 2 - o C. When would be figure near the lower end of the range be used? a) When the steam is known to be of good quality b) For short coils c) For small diameter coils d) When scaling or fouling of the coil takes place Answer: d) When scaling or fouling of the coil takes place 91. Steam coils should enter and leave the top of a tank when: a) The tank contains a corrosive solution b) When agitation of the tank solution is required c) When steam locking the trap draining a base coil could occur d) When good heat distribution is required Answer: a) The tank contains a corrosive solution 92. What range of „U‟ values would you apply for mild steel jacket around a stainless steel tank containing a water and detergent solution? a) 285 – 480 b) 450 – 1140 c) 850 – 1700 d) 285 – 850 Answer: b) 450 to 1140 kJ/kg- o K 93. A 5 m x 4 m x 4 m room has an air temperature of 32 o C (psat = 4.559 kPaa, hg = 2559.9 kJ/kg) and the pressure is 101 kPaa. The mass of water vapor in air is 2.5 kg with Rv = 0.45 kJ/kg- o K. What is the relative humidity of the air? a) 94.08 % b) 74.08 % c) 84.08 % d) 64.08 % Answer: a) 94.08 % 17 Solution:        kPaa289.4 445 2733245.05.2 V TRm p v vvv v        %08.94%100 559.4 289.4 %100 p p RH d v                94. A tank is to be heated by direct steam injection. How will the quantity of heat required compare with steam coil heating? a) It depends on the temperature of the water being heated b) More heat will be required c) The same amount of heat will be required d) Less heat will be required Answer: c) The same amount of heat will be reuired 95. If the velocity of discharge from a fire hose is 15 m/s and the hose is oriented 45 o from the horizontal. Disregarding air friction, determine the maximum range of the discharge. a) 14 m b) 33 m c) 24 m d) 23 m Answer: d) Maximum range, R = 23 m Solution:   m23m94.22 8066.9 90sin15 g 2sinV g cossinV2 R o22 o 2 o      96. Which of the following parameters has the greatest limiting effect on the thermal performance of an open, evaporative cooling tower? a) Wet-Bulb temperature b) Dry-Bulb temperature c) Range c) Approach Answer: a) Wet-bulb temperature Note: It is not possible to cool the water below the air‟s wet-bulb temperature. Thus, the WB temperature, more than any other parameter, sets the absolute limit on the cooling tower‟s capacity. 97. A full cylindrical tank 12 m high has a constant diameter of 6 m. The tank has a 100 mm diameter hole in its bottom. The coefficient of discharge for the hole is 0.98. How long will it take for the water level to drop from 12 m to 6 m? a) 16 minutes b) 20 minutes c) 24 minutes d) 28 minutes Answer: c) the time to lower the level = 24 minutes Solution:      s/m035.15128066.9298.0gH2CV vo      322 T m65.1696126 4 hD 4 V               s/m1181.0035.1510.0 4 Vd 4 AVQ 32 o 2 o                  utesmin94.23 601181.0 65.169 Q V t T  98. Air enters a cooling tower at 10 o C DB and 9.5 o C WB temperature. It leaves the tower saturated at 21 o C. Which condition is a likely outcome of this? a) Sublimation b) Condensation c) Adsorption d) Fog Answer: d) Fog Note:  The process has the potential to create fog, which consists of liquid droplets suspended in the atmosphere.  Adsorption is a process in which molecules of gas or liquid are extracted from an atmosphere. But it does not indicate suspended moisture droplets such as those that characterize fog. 99. A gaseous mixture of propane (C3H8), methane (CH4), and ethane (C2H6) have partial pressure 50 kPa, 95 kPa, and 115 kPa respectively. Determine the mass percentage of propane. a) 30.68 % b) 28.68 % c) 21.68 % d) 32.68 % 20 110. There are 20 kg of exhaust gas formed per kg of fuel oil burned in the combustion of diesoline C16H32. What is the excess air percent? a) 30.1 % b) 29.16 % c) 21.5 % d) 30.6 % Answer: b) 29.16 % Solution:        fuelkg/kg74.14 321612 3225.01628.137 mn12 m25.0n28.137 Wa        kg/kg19fuelkg1Fuelkg/kg20Waa  Percent Excess Air:   %16.29%100 74.14 74.1419 %100 W WW e a aaa                  111. A process that the body uses to convert energy in food into heat and work, or it is the process that determines the rate at which energy is converted from chemical to thermal form within the body. a) Metabolism b) Eating c) Body food processing d) Blood circulation Answer: a) Metabolism 112. A Diesel power plant uses fuel with heating value of 45 038.8 kJ/kg. What is the density of fuel at 30 o C? a) 0.7882 kg/li b) 0.8782 kg/li c) 0.9887 kg/li d) 0.8878 kg/li Answer: b) 0.8782 kg/li Solution:   kg/kJAPI6.13913041HHV o  28 6.139 130418.03845 6.139 13041HHV APIo      8871.0 5.13128 5.141 5.131API 5.141 SGo           8782.0 56.15300007.01 8871.0 tt0007.01 SG SG o o t      li/kg8782.0t  113. What is a body insulation that is usually described as a single equivalent uniform layer over the whole body? a) Skin b) Blood c) Clothing d) Water Answer: c) Clothing 114. What is the insulating value of clothing? a) Btu unit b) Clo units c) Calorie unit d) Frigorie Unit Answer: b) Clo units 115. Which of the following is the value of clo units? a) Btu HrftF 880.0clo1 2o   b) kW mF 100clo1 2o   c) W mF 275.0clo1 2o   d) kW mF 190clo1 2o   Answer: a) Btu HrftF 880.0clo1 2o   116. Determine the friction power of an engine if the frictional torque developed is 0.30 kN-m running 1200 rpm. 21 a) 47.7 kW b) 37.7 kW c) 43.3 kw d) 33.3 kW Answer: b) 37.7 kW Solution:    kW7.37 30 30.01200 30 nT FP f      117. A 500 kW Diesel engine operates at 101.3 kPaa and 27 o C in Calamba City. If the engine will operates in Baguio City having 93 kPaa and 23 o C, what new brake power will be developed if mechanical efficiency is 85 %. a) 455.96 kW b) 549.10 kW c) 954.1 kW d) 495.1 kW Answer: a) 455.96 kW Solution: 56.288 T 760 B BPBP se        h 1000 312.83 760B        h 1000 5.6 56.288T        Where, Ps = power at sea level, kW Pe = power at a given elevation, kW T = temperature at a given elevation, o K h = elevation, m T = temperature at a given elevation, o K. B = atmospheric pressure at a given elevation, mm Hg,   kW96.455 27327 27323 3.101 93 500BPe           118. What is the basic index used to describe the radiant conditions in a space, it is the mean temperature of individual; exposed surfaces in the environment? a) Index temperature b) Mean radiant temperature c) Space temperature d) Dry bulb temperature Answer: b) Mean Radiant Temperature 119. Fish weighing 11 000 kg with a temperature of 20 o C is brought to a cold storage and which shall be cooled to – 10 o C in 11 hours. Find the required plant refrigerating capacity in TR if the specific heat of fish is 0.7 kCal/kg- o C above freezing and 0.30 kCal/kg- o C below freezing point that is – 3 o C. The latent heat of freezing is 55.5 kCal/kg. a) 25.26 b) 14.38 c) 15.26 d) 24.38 Answer: d) 24.38 TR Solution:     4334p232112p ttchttcmQ            TR37.24 517.3 10330.05.553207.0187.4 360011 11000 Q          120. In order to avoid cavitation in a centrifugal pump, which of the following is true? - 10 o C 20 o C - 3 o C 1 2 3 4 22 a) Installation NPSH  pump NPSH b) Installation NPSH  pump NPSH c) Installation NPSH < pump NPSH d) Installation NPSH should be negative Answer: a) Installation NPSH  pump NPSH 121. A refrigeration system operates on the reversed Carnot cycle. The minimum and maximum temperatures are – 25 C and 72 C, respectively. If the heat rejected at the condenser is 6000 kJ/min, find the tons of refrigeration required. a) 20.44 TR b) 24.40 TR c) 42.20 TR d) 44.20 TR Answer: a) 20.44 TR Solution:       tons44.20 517.360 24839.17 517.3 TS 517.3 Q TR LL    122. What always accompanies an isentropic expansion of steam? a) An increase in entropy b) An increase in enthalpy c) A decrease in entropy d) A decrease in enthalpy Answer: d) A decrease in enthalpy 123. Those substance that are particularly variable in the moisture content that they can possess at different times. a) Wet materials b) Hygroscopic materials c) Gross materials d) Bone-dry-weight material Answer: b) Hygroscopic material 124. The hygroscopic moisture content of a substance expressed as a percentage of the bone-dry-weight of the material. a) Moisture content b) Regain c) Bone-dry-weight d) Gross weight 125. What is the advantage of a pressurized deaerator over an atmospheric deaerator? a) A boiler feed tank is no longer required b) Less over all energy will be required to produce the steam c) It can be fitted at ground level d) It removes more oxygen Answer: d) It removes more oxygen 126. In proximate analysis, the coal analysis is consisting of moisture content, fixed carbon, ash, and which of the following? a) Sulfur b) Hydrogen c) Nitrogen d) Volatile matter Answer: d) Volatile matter 127. How do you call the heating value of the fuel if the water in the products of combustion is in the liquid state? a) Higher heating value b) Lower heating value c) Proximate heating value d) Gravimetric heating value Answer: a) Higher heating value 128. What is the rate, in Btu/h or W, at which heat must be added to the conditioned space to maintain a constant temperature and sometimes a specified relative humidity? a) Space heat gain b) Space cooling load c) Space heating load d) Space heat extraction rate Answer: c) Space heating load 129. Space heat extraction rate Qex, Btu /h (W), is the rate at which heat is actually removed from the conditioned space by the air system. Its sensible heat rate component is equal to the sensible cooling load only when the space air temperature remains constant. a) Space heat gain b) Space cooling load c) Space heating load d) Space heat extraction rate Answer: d) Space heat extraction rate 130. It is the rate, in Btu/h or W, of heat transfer at the coil. Its cooling load component is the rate at which heat is removed by the chilled water flowing through the coil or is absorbed by the refrigerant inside the coil. What do you call this? a) Coil load b) Heating coil load c) Refrigerating load d) Cooling load 25 Answer: a) Detergents 150. What is the molecular attraction of layers of an unlike matters? a) Adhesion b) Cohesion c) Advection d) Convection Answer: a) Adhesion 151. How do you call these engine oil additives used to prevent attack on iron and steel surfaces by condensed moisture and acidic corrosion products, aggravated by low-temperature stop-and-go operation? a) Detergents b) Dispersants c) Oxidation inhibitors d) Rust inhibitors Answer: d) Rust inhibitors 152. How do you call these engine oil additives used to help enable adequate low-temperature flow, along with sufficient viscosity at high temperatures? a) Viscosity-index improvers b) Pour point dispersants c) Oxidation inhibitors d) Rust inhibitors Answer: a) Viscosity-index improvers 153. These oil additives are used to minimize wear under boundary lubrication conditions, such as cam and lifter, and cylinder-wall and piston-ring surfaces. a) Anti-wear additives b) Pour point dispersants c) Oxidation inhibitors d) Rust inhibitors Answer: a) Anti-wear additives 154. These are engine oil additives used to allow air to break away easily from the oil. a) Anti-wear additives b) Defoamants c) Oxidation inhibitors d) Rust inhibitors Answer: b) Defoamants 155. These engine oil additives are used to improve fuel efficiency by reducing friction at rubbing surfaces. How do you call these oil additives? a) Anti-wear additives b) Friction modifiers c) Oxidation inhibitors d) Rust inhibitors Answer: b) Friction modifiers 156. How do you call an opening where hot source of energy from the earth is harnessed? a) Crater b) Hot water source c) Fumarole d) Volcano opening Answer: c) Fumarole 157. At standard atmospheric conditions, what is the approximate speed of sound? a) 336 m/s b) 363 m/s c) 633 m/s d) 346 m/s Answer: a) 336 m/s 158. The speed of sound is also called as: a) Sound velocity b) Acoustic velocity c) Subsonic velocity d) Critical velocity Answer: b) Acoustic velocity 159. This is the velocity at which a small pressure wave moves through a fluid. How do you call this velocity? a) Sonic velocity b) Subsonic velocity c) Supersonic velocity d) Hypersonic velocity Answer: a) Sonic Velocity 160. Which of the following is the speed of light? 26 a) 2.998 x 10 8 m/s b) 2.998 x 10 9 c) 2.998 x 10 10 m/s d) 2.998 x 10 7 m/s Answer: a) 2.998 x 10 8 m/s 161. What can you say about entropy in the universe? a) Entropy is always increasing b) Entropy is decreasing c) Entropy will zero at the end of time d) Entropy is stagnating Answer: a) Entropy is always increasing 162. Which of the following is the chemical formula of butane? a) C2H5 b) C10H16 c) C4H10 d) C3H6 Answer: c) C4H10 163. If the sensible heat ratio is 0.75, what does it mean? a) 75 % latent heat and 25 % sensible heat b) 75 % sensible heat and 25 % latent heat c) 25 % latent and sensible heat and 75 % latent heat d) 75 % sensible and latent heat and 25 % sensible heat Answer: b) 75 % sensible heat and 25 % latent heat 164. The hardness of ground water required as feed water for a boiler is 0 – 10 ppm (part per million), which of the following is the range of alkalinity requirement? a) pH 9 to pH 10 b) pH 6 to pH 10 c) pH 10 to pH 11 d) pH 8 to pH 10 Answer: c) pH 10 to pH 11 165. As used in the Revised PSME Code for Boilers and Pressure Vessels, it is any boiler which does not exceed any of the following limits: 405 mm inside diameter, 1065 mm overall length of outside to outside heats at center, 1.85 m 2 of water heating surface, and 7.03 kg/cm 2 maximum allowable working pressure. What is this boiler? a) Power boiler b) Portable boiler c) Miniature boiler d) Locomotive boiler Answer: c) Miniature boiler 166. It is a closed vessel in which steam or other vapor (to be used externally to itself) is generated by the direct application of heat used for power generation. How do you call this boiler? a) Power boiler b) Portable boiler c) Oil-fired boiler d) Miniature boiler Answer: a) Power boiler 167. It is a closed vessel intended for use in heating water of for application of heat to generate steam or other vapor to be used externally from it. What do you call this pressure vessel? a) Boiler or steam generator b) Fired pressure vessel c) Unfired pressure vessel d) Pressurized tank Answer: a) Boiler or steam generator 168. What do you call a vessel in which pressure is obtained from external sources, or from an indirect application of heat? a) Boiler or steam generator b) Fired pressure vessel c) Unfired pressure vessel d) Pressurized tank Answer: c) Unfired pressure vessel 169. It is any boiler or unfired pressure vessel constructed, installed, placed in operation but subject to annual inspection. What do you call this? a) Miniature boiler b) Existing installation c) New boiler d) Portable boiler 27 Answer: b) Existing installation 170. It is a boiler that has been inspected and declared unsafe to operate or disqualified, marked and marked indicating its rejection. How do you call this boiler? a) Second hand boiler b) Reinstalled boiler c) Condemned boiler d) Unfired boiler Answer: c) Condemned boiler 171. When new boilers are installed in either existing or new buildings, a minimum height of at least ______ shall be provided between top of the boiler proper and ceiling. a) 1050 mm b) 2130 mm c) 1250 mm d) 2050 mm Answer: b) 2130 mm 172. For power boilers, when the tensile strength of steel is not known, it shall be taken as 379 MPa and which of the following for the wrought iron? a) 379 N/mm 2 b) 310 MPa c) 450 MPa d) 521 N/mm 2 Answer: b) 310 MPa 173. Name one characteristic feature of mechanical steam traps. a) They pass condensate at steam temperature b) They operate by sensing condensate temperature c) They can be fitted into any position d) They are not affected by increasing back pressure Answer: b) They pass condensate steam temperature 174. In a mechanical steam trap, why is a float trap better at venting air than an inverted bucket trap? a) A float can quickly adjust to the presence of air b) A float is fitted with an automatic air vent c) A float trap does not vent air better than bucket trap d) The air vent orifice is adjustable on a float trap Answer: b) A float fitted with automatic air vent 175. In a mechanical steam trap, what added benefit does the automatic air vent offer to a float trap? a) It stops the trap from freezing in cold weather b) The trap can be use on larger backpressures c) It significantly increases the cold start-up capacity of the trap d) The condensate orifice can be the same size for all pressure gauges Answer: c) It significantly increases the cold start-up capacity of the trap 176. In a mechanical steam trap, what advantage does a bucket trap have over a float type? a) It is able to withstand waterhammer b) It can be used on higher pressure c) It can discharge air freely d) It cannot lose its water seal Answer: b) it can be used on higher pressure 177. A heat exchanger is designed to operate without waterlogging of the steam space. What is the usual choice of trap for its drainage? a) Thermostatic trap b) Inverted bucket trap c) Thermodynamic trap d) Float trap with thermostatic air vent Answer: d) Float trap with thermostatic air vent 178. Which is the best trap to use when steam locking can occur? a) An inverted bucket trap with an internal check valve mechanism b) A balanced pressure steam trap c) A float trap with automatic air vent d) A float trap with steam lock release mechanism 30 b) It does so at constant enthalpy and reducing temperature c) Both enthalpy and entropy reduce and temperature remains constant d) Both enthalpy and entropy increase Answer: c) Both enthalpy and entropy reduce and temperature remains cosntant 199. It is an increase in fluid pressure in a long pipe caused by a sudden velocity decrease, where the sudden decrease in velocity is caused by a valve closing. a) Aero dynamics b) Water hammer c) Terminal velocity d) Drag Answer: b) Water hammer 200. It is an upward force that is exerted on an object (like flat plate, airfoil, rotating cylinder, etc.) as the object passes through a fluid. What do you call this? a) Drag b) Lift c) Aero horsepower d) Terminal velocity Answer: b) Lift 201. What is a frictional force that acts parallel but opposite to the direction of motion of fluid? a) Drag b) Lift c) Aero horsepower d) Terminal velocity Answer: a) Drag 202. It is a term used by automobile manufacturers to designate the power required to move a car horizontally at 50 mi/hr against the drag force. What is this? a) Mechanical horsepower b) Aero horsepower c) Fuel power d) Fluid power Answer: b) Aero Horsepower 203. A manufacturer claims that it has a COP of 2.0 when cooling a food at 5 o C using ambient air at 30 o C as a heat sink. Is the claim of the manufacturer valid? a) Yes b) No c) Probably d) It needs experimental verification Answer: a) Yes, because the claimed COP of the manufacturer is lower than the COP of Carnot Refrigeration 204. What can you say about the velocity of fluid at the center of the pipe section? a) Maximum b) Minimum c) Average d) Zero Answer: Maximum, the velocity of the flowing fluid is maximum at the pipe center 205. Continuity equation is applicable to which of the following? a) Viscous and unviscous fluids b) Compressibility fluids c) Conservation of mass d) Steady and unsteady flows Answer: c) Conservation of mass 206. Hygrometer is an instrument used to determine of which of the following? a) Specific gravity of fluids b) Specific gravity of gases c) Specific gravity of liquids d) Specific gravity of solids Answer: a) Specific gravity of fluids 207. At critical point of a pure substance, what is the value of latent heat? a) Maximum b) Minimum c) Zero d) Below zero Answer: c) Zero, at the critical point hg – hf = 0 208. Which of the following is a function of a steam nozzle? a) Converts kinetic energy into heat energy b) Changes internal energy into kinetic energy 31 c) Converts potential energy into heat energy d) Changes enthalpic energy into kinetic energy Answer: d) Changes in enthalpic energy is converted into changes in kinetic energy 209. Generally steam turbines in power station operate at which of the following speeds? a) 3000 rpm b) 1000 rpm c) 4000 rpm d) 500 rpm Answer: c) 4000 rpm 210. Tidal power is the power generated from which of the following? a) Waves of the ocean b) Thermal energy of ocean water c) Raw sea water d) Rise and fall of tides Answer: d) Rise and fall of tides 211. Which of the following is an expression or equivalent of horsepower per ton of refrigeration? a) COP 715.4 b) 715.4 COP c) COP x 4.715 d) COPx715.4 1 Answer: a) 4.715 divided by the COP 212. It is the ratio of the amount of heat taken up by a substance to the temperature at which the substance exists. How do you call this? a) Internal energy b) Flow energy c) Enthalpy d) Entropy 213. Which of the following is a type of water turbine where a jet of water is made to fall on the blades or buckets and due to the impulse of water the turbine starts moving? a) Reaction turbine b) Steam turbine c) Francis turbine d) Pelton wheel 214. What do you call a fan in which the fluid is accelerated parallel to the fan axis? a) Axial centrifugal fan b) Mixed flow centrifugal fan c) Radial centrifugal fan d) Francis type fan 215. It represents the loss due to mechanical friction of the moving parts of the engine, and expressed as horsepower. How do you call this? a) Indicated Hp b) Brake Hp c) Combined Hp d) Friction Hp 216. How do you call a device or engine which continually and indefinitely discharged more energy than it receives? a) Carnot engine b) Generating machine c) Stirling engine d) Perpetual motion machine 217. In plotting the bHp versus speed in a wide open throttle test for a spark ignition engine, the bHp curve: a) is a Straight line b) tends to concave downward c) has no characteristic shape d) tends to concave upward 218. Upon entering the boiler room, you find the water out of the glass, the safety valve blowing off strong, and a fire under the boiler. Your first action would be to: a) Remove the fire with draft and damper open b) Cool the boiler down completely c) Prevent priming by not raising the safety valve or making change in operating of engines or boiler d) Cool the boiler down completely and prevent priming by not raising the safety valve 219. The A.S.M.E. Boiler code for boiler shells requires a tensile strength of which of the following, in psi? a) 10000 to 20000 b) 25000 to 45000 c) 55000 to 63000 d) 70000 to 85000 220. The best time to blow a boiler down is: a) Once a day when the load is lightest b) Once a day under full load c) When the chemical concentration is greatest d) Once a shift 221. In performing a hydrostatic test on an existing power boiler, the required test pressure must be controlled so that it is not exceeded by more than: a) 2% b) 4% c) 6% d) 8% 222. The first step to take in planning a preventive maintenance program is to: a) Replace all electric wiring b) Make an equipment inventory c) Replace all pump seals d) Repair all equipment which is not in operation 223. Which of the following is the most important consideration in a fire prevention program? a) Train the staff to place flammable in fireproof containers b) Know how to attack fires regardless of size c) See that halls, corridors, and exits are not blocked d) Detect and eliminate every possible fire hazard 224. Which of the following types of portable fire extinguisher is recommended as most effective for putting out oil fires? 32 a) Pump tank type b) Cartridge actuated type c) Soda acid type d) Foam type 225. Which of the following are the four stages of the warning system designated by the high air pollution alert warning system? a) Initial, chronic, acute, penetrating b) Forecast, alert, warning, emergency c) Light, medium, heavy, extra heavy d) Early, moderate, severe, toxic 226. The chemical most commonly used to speed sedimentation of sewage is known as: a) Lime b) Copper sulfate c) Sulfuric acid d) Methylene blue 227. Most of the bacteria in sewage are: a) Saprophytic b) Dangerous c) Parasitic d) Pathogenic 228. One of the two types of non-material nuclear radiation is: a) Gamma radiation b) Transmutation radiation c) Walton radiation d) Betatron radiation 229. Which of the following is not a qualification for an applicant for ME board examination: a) A certified plant mechanic b) At least 18 years old c) A holder of BSME degree d) A citizen of the Philippines 230. A thermo hydraulic feed water regulator is used to regulate the flow of water to a drum type boiler. The amount of water input to the boiler is controlled in proportion to the: a) Boiler load b) Setting of the feed pump relief valve c) Amount of water in the outer tube that flashes into steam d) Water level in the drum 231. The standard capacity rating conditions for any refrigeration compressor is: a) 5oF, 19.6 psig for the suction 86oF, 154.5 psig for the discharge b) 5oF, 9.6 psig for the suction 96oF, 154.5 psig for the discharge c) 10oF, 9.6 psig for the suction 96oF, 144.5 psig for the discharge d) 5oF, 19.6 psig for the suction 96oF, 134.5 psig for the discharge 232. In accordance with the air pollution control code, no person shall cause or permit the emission of air contaminants from a boiler with a capacity of 500 million BTU sulfur dioxide content of more than: a) 300 parts per million by volume undiluted emissions measured at 15 percent excess air b) 200 parts per million by volume of undiluted emissions measured at 10 percent excess air c) 200 parts per million by volume undiluted emissions measured at 15 percent excess air d) 300 per million by volume undiluted emissions measured at 10 percent excess air 233. Assume that one of your assistance was near the Freon 11 refrigeration system when a liquid Freon line ruptured. Some of the liquid Freon 11 has gotten into your assistant‟s right eye. Of the following actions, the one which you should not take is to: a) Immediately call for an eye doctor specialist (medical doctor) b) Gently and quickly rub the Freon 11 out of the eye c) Uses a boric-acid solution to clean out the Freon 11 from his eye d) Wash the eye by gently blowing the Freon 11 out of his eye with air 234. As compared to a power-driven triplex single-acting pump of the same size and operating at the same speed, a steam-driven duplex double-acting pump will: a) Pump more water per minute b) Give a more uniform discharge c) Have a higher first cost d) Be more economical to operate 235. It is a device commonly used to cool condenser water in Power and Refrigeration plants. The function of which is to reject heat to the atmosphere by reducing the temperature of water circulated through condenser or other heat rejection equipment. What is this device commonly called? a) Condenser b) Cooler c) Cooling tower d) Evaporator 236. It is a type of dryer in which the gases of combustion pass through the spaces surrounding, or in other ways heating, the drying chamber, but the gases are not allowed in contact with the material being dried. What is this dryer? a) Direct-heat type dryer b) Indirect-heat type dryer c) Steam-heated type dryer d) Rotary Dryer 237. In a refrigeration system, which of the following would cause a high suction pressure? a) Expansion valve not open wide enough b) Expansion valve open too wide c) King valve not open wide enough d) Dirty dehydrator 238. In the deep well installing or operation, the difference between static water level and operating water level is called: a) Suction lift b) drawdown c) priming level d) clogging 239. Which of the following is an characteristics of an impulse turbine? a) Steam striking blades on angle b) No steam reaction to velocity c) Steam striking blades at zero angle d) Steam reversing direction 240. Gas produced by the combustion of fuel oil and cannot be found in the flue gases is: a) Carbon dioxide b) Hydrogen c) Oxygen d) Nitrogen 241. Scale in boiler can: a) Create low steam quality b) Cause foaming c) Overheat blow off line d) Inhibit circulation and heat transfer 242. The effectiveness of a body as a thermal radiator at a given temperature: 35 275. Which of the following are principal dissolved solids that are scale forming? a) Carbonates and sulphates of sodium b) Calcium bicarbonate c) Carbonates and sulphates of magnesium d) Bicarbonate of sodium and magnesium 276. What is the effect of temperature on calcium and magnesium sulphates? a) They separate out as soft scale and sludge b) They precipitate out solution and form hard scale c) Foaming and carryover occurs d) The TDS is increased 277. What is the treatment for scale forming salts in boiler feedwater? a) They are chemically treated to modify the pH b) The feedwater tank is raised to at least 85 oC c) They are chemically treated to produce suspended solids d) They are removed by filtration means 278. Which of the following types of alcohol is the most frequently considered as fuel for internal combustion engine? a) Methyl alcohol b) Isopropyl alcohol c) Ethyl alcohol d) Alcogas 279. In a thermal plant, name the components of a self-acting temperature control system. a) Control valve and actuator b) Control valve, actuator and sensor c) Control valve, actuator, capillary tube and sensor d) Control valve, actuator and capillary tube 280. What is the purpose of over temperature protection within the self-acting control system? a) To protect the valve from high temperature steam b) To protect the liquid fill in the capillary from boiling c) To protect the control system from irreversible damage d) To protect the application from overtemperature 281. Why are three-port self-acting control valves used in an industrial steam of a thermal system? a) To mix or divert liquids especially water b) To dump steam to waste under fault conditions c) Where cooling applications are required d) When large valves are required to meet large capacities 282. How do you call a process in which superheated steam is either restored to its saturated state, or its superheated temperature is reduced? a) Superheating b) Reheating c) Regenerative heating d) Desuperheating 283. What does MAWP stand for/ a) Maximum attenuated working pressure b) Maximum allowable working pressure c) Maximum allowable with pressure d) Minimum allowable working pressure 284. Name one disadvantage of a direct acting pressure reducing valve. a) It only has proportional control b) It has proportional and integral control but no derivative control c) It operates in an o/off fashion d) An external power source is required for it to operate 285. In order to avoid cavitation in a centrifugal pump, which of the following is true? a) Installation NPSH  pump NPSH b) Installation NPSH  pump NPSH c) Installation NPSH < pump NPSH d) Installation NPSH should be negative 286. It is dust removal equipment that consists of a cylindrical tank structure provided with a tangential opening at one end for gas passage and a spray manifold at the center which is made of a vertical pipe attached with spray nozzles where water is introduced at the bottom of this spray pipe. The gas revolves around the cylindrical body as it enters the scrubber, and comes in contact with the water spray, the dust fly ash are then wetted and hence separated from the gas leaves the scrubber at the top. a) Cinder trap or catcher b) Cyclonic Spray Scrubber c) Cyclone Separator d) Electrostatic Precipitator 287. What is a heat exchanger that allows cross contact between two media? This heat exchanger allows the cooling water to flow by gravity over the outside of tubes or plates. a) Single-pass heat exchanger b) Double-pass heat exchanger c) Baudelot heat exchanger d) Shell-and-tube heat exchanger 288. What is the recommended weight of the machine foundation? a) 3 to 5 times the machine weight b) 4 to 6 times the machine weight c) 2 to 4 times the machine weight d) 2 to 4 times the machine weight 289. It is a bituminous coal that contains plenty of hydrocarbons, forming lumped masses when burned. This coal is ideal for forming carbonaceous gases for reduction of ore. What do you call this coal? a) Coking or coking coal b) Free burning coal c) Peat coal d) Lignite coal 290. It is an engine in which the connecting rod is directly connected to the piston wristpin. The side thrust caused by the angularity of the connecting rod is taken by the piston bearing against the cylinder wall. a) Opposed-piston engine b) Trunk piston engine c) Crosshead engine d) 2-stroke engine 36 291. It is an internal combustion engine wherein the ignition of the fuel is not accomplished solely by the heat developed from the compression of the combustion air supplied but partly or entirely by other heat sources, such as an uncooled tube, plate, bulb, or an electric resistance coil. a) Spark-ignition engine b) Compression-ignition engine c) Surface-ignition engine d) Dual combustion engine 292. This is the condition in a geothermal plant wherein the ground surface where the well is drilled is depressed or subsides due to depleting. What do you call this? a) Ground subsidence b) Thermal pollution c) Chemical pollution d) Dissolved solids 293. In the critical thickness of insulator concept for a cylinder, what does the Biot number indicate if its value is less than 1? a) Condition for optimum heat flow b) Addition of insulation will increase heat transfer rate c) Additional insulation will decrease the heat transfer rate d) Heat transfer rate reaches a maximum 294. How do you call the ratio of the product of a convective heat transfer coefficient and the critical radius of the insulator to that of the thermal conductivity of the insulator? a) Biot number b) Prandlt number c) Nusselt number d) Reynolds number 295. This is a type of dryer that consists of a vertical shaft in which the wet feed is introduced at the top and falls downward over baffles while coming in contact with the hot air that rises and exhaust at the top. This dryer is used for drying palay, wheat, and grains. a) Rotary dryer b) Hearth dryer c) Tower dryer d) Tray dryer 296. How do you call those substances that are particularly variable in the moisture content that they can possess at different times? a) Wet materials b) Hygroscopic materials c) Gross materials d) Bone-dry-weight material 297. The bottom blow down on a boiler is used to: a) Remove mud drum water impurities b) Increase boiler priming c) Reduce steam pressure in the header d) Increase the boiler water level 298. In a Brayton cycle or gas turbine cycle, what do you call the heat exchanger that passes exhaust heat to the compressed air, prior to combustion? a) Reheater b) Recuperator c) Heater d) Heat exchanger 299. The heat rejected by the working substance to the regenerator in the Stirling cycle is: a) Equal to the heat absorbed by the working substance from the regenerator b) Not equal to the heat absorbed by the working substance from the regenerator c) Dependent on the value of temperature in the heat addition process d) Measured during the constant temperature heat rejection process 300. How do you call a device that converts liquid refrigerant to vapour, with the help of the surrounding heat? a) Condenser b) Expansion valve c) Compressor d) Evaporator 301. In gas compressor, when the volumetric efficiency increases, the piston displacement has: a) Not been changed b) Been decreased c) Been increased d) Been insufficient data 302. The ratio of its radiating power to that of a black body at same temperature. a) Transmissivity b) Reflectivity c) Absorptivity d) Emissivity 303. Fans used to withdraw air under suction, that is, the resistance to gas flow is imposed primarily upon the inlet. a) Blowers b) Exhauster c) industrial fans d) Domestic fans 304. The phenomenon of rising water in the tube of small diameter is called what? a) Surface tension b) Capillary rise c) Water gage rise d) Fluid column rise 305. Pitot tube is used to measure, a) Height b) Velocity c) Viscosity d) Density 306. During engine operation, to vary the air quantity and also to vary the air fuel mixture, this is used to pen and closed the inlet manifold. a) Throttle valve b) Check valve c) Choke valve d) Gate valve