Sida a cholón, Apuntes de Turismo

¡Descarga Sida a cholón y más Apuntes en PDF de Turismo solo en Docsity! 22 06-2011 elektor TesT & MeasureMenT Measure Gamma Rays with a Photodiode Radiation detector using a BPW34 Ionising radiation is potentially harmful to health, and it is important to minimise one’s exposure to it as far as possible. A sim- ple Geiger counter with a small glass mantle tube will not usually be adequate to detect possibly harmful radiation. The semicon- ductor sensor we describe below also has a relatively low sensitivity, only being able to detect fairly intense sources of radia- tion, but it is nevertheless an interesting device for carrying out experiments and measurements. An advantage of using a photodiode is its small sensitive area. The background rate due to cosmic rays is very low and signals from small samples are easier to detect than with a counter tube. Radiation When considering protection from radia- tion it is gamma rays that are the most important. They can penetrate walls and it is difficult to block them. Hard gamma rays are present in the environment all around us and are also not stopped even by a thick wall. Alpha particles, on the other hand, only have a short range and generally can- not even penetrate a sheet of paper: this is the reason that many counter tubes can- not detect them, unless they have a very thin mica window. Beta particles have a longer range and can penetrate thin sheets of metal. Most counter tubes are mainly designed for detecting gamma rays while, within certain limitations, also being sensi- tive to beta particles. Diode as detector The behaviour of a type BPW34 PIN photo- diode is similar to that of a low-cost coun- ter tube. Alpha particles will be stopped by the plastic enclosure of the device, whereas gamma rays pass through without prob- lem and create many electron-hole pairs in the diode’s depletion layer. If the diode is reverse-biased, almost all of the charge car- riers will be drawn away: this corresponds to a small current pulse which can be ampli- fied and processed. Beta particles can also generate such a signal if they are sufficiently energetic to reach the depletion layer. The amplitude of the signal produced by the photodiode is considerably smaller than that normally obtained from a counter tube, and so a very low-noise instrumentation amplifier circuit is needed. Another requirement when using a photodi- ode as a beta and gamma radiation detector is that light must be completely excluded, as otherwise the photocurrent will over- whelm the signal we are looking for. In our prototype we used ordinary aluminium kitchen foil as a screen. The difference between PIN diodes and PN diodes is that the former include an extra very lightly N-doped region called the ‘intrinsic’, or ‘i’ region. This high-resistance region lies between the ‘n’ and ‘p’ regions. The result is a wider depletion layer in the diode, and hence a greater volume of semi- conductor that can interact with photons. The structure is used in a photodiode in by Burkhard Kainka (Germany) The first device that springs to mind when thinking about measuring radioactivity is the Geiger-Müller tube. However, these counter tubes are getting hard to find and expensive, and even if you do manage to get hold of one, you will still need to find a way to generate its operating voltage of several hundred volts. It is less well known that even a humble photodiode such as the BPW34 can be used to detect X-rays and gamma radiation. Personal Download for doll, pol | copyright Elektor 815126 23elektor 06-2011 TesT & MeasureMenT order to obtain as many charge carriers as possible per photon, optimising the device’s sensitivity. Another way to increase sensitivity is to increase the sensitive area of the device. However, this has the disad- vantage of increasing its capacitance, which reduces the (voltage) amplitude of its output signal. Commercially-avail- able semiconductor radiation detectors have a large area and a wide intrinsic region. Simple PIN photodiodes such as the BPW34 are less sensitive than these devices, but also of course somewhat cheaper. The BPW34 and BPX61 photodiodes are practically identical apart from their enclo- sures. The (cheaper) BPW34 comes in a plastic package, whereas the BPX61 comes in a TO-5 metal enclosure with a glass win- dow. It is possible to remove this window (carefully!) to expose the chip: this will make the diode capable of detecting alpha particles. The rays or particles must first make it through a 15 µm thick piece of aluminium (the thickness of ordinary kitchen foil). This is no obstacle to gamma rays and beta par- ticles, and alpha particles with an energy of 4 MeV or more will also pass through. When the particle enters the plastic of the photo- diode package, deceleration radiation (Ger- man: ‘bremsstrahlung’) will be produced in the form of brief flashes of light, which can also sometimes be detected by the sensor. It is therefore not impossible for even the BPW34 to have some sensitivity to alpha particles. In principle any semiconductor is sensi- tive to ionising radiation. It is perhaps less surprising, then, that a photodiode is sen- sitive to radiation than that the effect has not been widely remarked on before. The effect is however well known in dynamic RAMs, whose stored data can be corrupted by incident radiation. The problem of build- ing electronics to withstand the higher lev- els of radiation found in space is becoming increasingly difficult, because as structures get smaller it becomes increasingly likely that a single energetic particle can interfere with the operation of a circuit. Amplifier In the literature charge amplifiers are usu- ally constructed using a low-noise FET-input opamp as the input stage. Here we take an alternative approach: Figure 1 shows the circuit of the sensor amplifier. Two tran- sistors are used to amplify the signal from the photodiode. The direct-coupled ampli- fier automatically sets itself to a mid-range operating point, which gets a good signal- to-noise ratio from the low-noise BC549C transistors. The transistor input of the amplifier has a comparatively low impedance, which gives good noise matching. As a result of its base-collector capacitance the first stage also operates as an integrator: this turns the brief pulses from the photodiode into longer pulses which can then more easily be amplified. Sensitivity can also be increased by increas- ing the reverse voltage on the diode. This reduces the capacitance of the diode and increases the size of the depletion layer. The voltage can be as high as 32 V, although the optimum value probably lies somewhat lower: the diode already operates well at 9 V. It is also possible to wire two or more photodiodes in parallel, and that way it is possible to achieve a sensitivity on a par with that of a small counter tube such as the ZP1310. An oscilloscope can be connected to the output of the circuit to view the signal. Readers who yearn for the clicking sound of a ‘real’ Geiger counter should consult the text box ‘From radiation to sound’ for a suit- able solution. Construction The circuit can be built on a piece of bread- board (see Figure 2), with the photodi- ode on the underside (Figure 3). To keep light out of the sensor the whole circuit is wrapped in aluminium foil (Figure 4). As mentioned above, ordinary kitchen foil is D1 BPW34 T1 BC549C T2 BC549C R4 4k 7 R3 22 0k R5 1k C2 10u 16V C3 100u 16V R2 2M2 R1 220k C1 100n K1 +9V 110372 - 11 Figure 1. The amplifier circuit. Figure 2. Prototype of the sensor amplifier. Figure 3. The sensor is on the underside of the board. Personal Download for doll, pol | copyright Elektor 815126